BRYSTON 4B SST MANUAL PDF

BRYSTON OWNER’S MANUAL Instructions For Bryston SST Series Amplifiers Models 3B SST and 4B SST 3B SST and 4B SST Series Amplifiers Table of. Audio manuals and audio service pdf instructions. Find the user manual you need for Bryston 4B SST Stereo Amplifier User Manual. Page 1. Page 2. Page 3. User guide • Read online or download PDF • Bryston 4BSST User Manual • Bryston Receivers and Amplifiers.

Author: Shaktigami Nikogis
Country: Maldives
Language: English (Spanish)
Genre: Travel
Published (Last): 2 February 2008
Pages: 308
PDF File Size: 2.73 Mb
ePub File Size: 20.39 Mb
ISBN: 254-7-90897-272-8
Downloads: 80905
Price: Free* [*Free Regsitration Required]
Uploader: Gocage

Bryston 4BSST User Manual | 8 pages | Also for: 3BSST

Cables should be kept as short as practical and should never be terminated with connectors that may become confused for AC power connectors. Gold plated locking banana plugs are available from Bryston. The above noise ratings represent minimum readings, actual readings may be better. When the channel has cooled to a safe operating condition ssg channel will return to normal operation. Bryston can provide an optional fan package if required.

Cables should be dressed away from input and power cables.

Thermal Shutdown orange Each channel has thermal shutdown circuitry to prevent damage due to overheating. Never operate the amplifier in a vertical position.

Note that copper wire is malleable and may require further tightening after the initial installation. Then power the unit up normally.

Bryston Stereo Amplifier 4B SST User Guide |

The power up or turn-on of the 4B SST may be activated by remote control voltage. In the unlikely event you have a problem and must return it for service you must use the proper packing material. Bryston welcomes any suggestions you may have, or comments regarding the operation of your amplifier. Balanced systems provide manal rejection from external electrical interference, so cable length can be very long 50m or longer.

  CATERPILLAR 908H2 PDF

In general never use longer cables than necessary, never coil excess cable length, and keep signal wires away from AC power or speaker cables. It’s a community-based project which helps to repair anything. Also see installation section on ventilation. The power up or turn-on of the 3B SST may be activated by remote control voltage.

Bryston C Series 4B SST Dimensional Drawing

The 2v setting provides an amplifier gain – 23 dB. The optimum gain setting will depend upon the source pre-amp operating level, and or byrston preference. Brystoh input Vs Single ended input: See diagram for details. Each SST channel gives the user the option of switching between either balanced input or single ended input. See figure 2 below. Input Sensitivity Gain Switch. In the event of a defect or malfunction, Bryston will remedy the problem by repair or replacement, as we deem necessary, to restore the product to full performance.

Should 4n breaker trip, lower or remove the amplifier input signals. The SST amplifier uses a magnetic-trip circuit breaker 1 to protect the amplifier.

The 1v setting provides the most amplifier gain – 29 dB. The RED binding post is connected to the amplifier output.

Lugs should be gold plated. Momentary clipping can be tolerated, however it indicates that maximum undistorted power has been surpassed and potential speaker damage may result if overload conditions persist. Each channel selects a gain of 29dB brystoj or 23dB 2v. On the rear panel is provided a high current plug for the power cord receptacle. Push again and the amplifier will power-down.

Master circuit – breaker. Persistent Thermal shutdown indicates steps need to be taken to increase airflow across the channel or channels heat sink. Spade lugs provide high contact area and secure fastening. Connect to this post the – terminal on the loudspeaker. This warranty is considered void if the defect, manua or failure of the product or any component part was caused by damage not resulting from a defect or malfunction st abuse while in the possession of the customer.

  FRATER UD MONEY MAGIC PDF

Push firmly the center of brywton switch until the power-up sequence begins. Do not over tighten or the binding post may become damaged. This includes parts, labour and return shipping to the first owner and all subsequent owners. When the power supplies have stabilized ss channel will come out of mute and the LED will change to green normal operation. Warranty coverage is automatic and commences with the original date of manufacture which is kept on file at Bryston.

Additional tightening pressure can be achieved using a coin in the slots of the knob.

Banana plugs offer a quick disconnect option. Any amplifier that is constantly operated into clipping indicates a more powerful amplifier is needed for that application. The voltage is listed on the label found at the upper right of the brytson panel.

The circuit feeding the 4B SST should be sufficient so as not to cause the circuit breaker to trip 15 amp min. Use quality wire, and if runs are more than 3 meters use at least 12 gage hryston. Before inserting a banana plug into the binding post be sure to tighten the post nut to avoid rattling and to provide full insertion of the banana plug. Check that the voltage rating on the label conforms with your locality. For this reason do wst install anything directly above it.

The 1v setting is used when the source is single-ended, or from a transformer coupled balanced source. The control current is determined by the source equipment.

Author: admin