ASTM D4633 PDF

Designation: D − 10Standard Test Method for Energy Measurement for This test method is under the jurisdiction of ASTM Committee D18 on Soil and. Purchase your copy of ASTM D – 16 as a PDF download or hard copy directly from the official BSI Shop. All BSI British Standards available. ASTM D ,. “Standard. Test Method for Stress Wave. Energy Measurement for Dynamic. Penetrometer. Testing. Systems”. [2], speclfles.

Author: Ararn Dolrajas
Country: Comoros
Language: English (Spanish)
Genre: Sex
Published (Last): 17 September 2007
Pages: 183
PDF File Size: 8.63 Mb
ePub File Size: 9.75 Mb
ISBN: 417-3-40259-261-7
Downloads: 49217
Price: Free* [*Free Regsitration Required]
Uploader: Kigagis

What is a standard?

Standard Test Method for Energy Measurement for Dynamic Penetrometers

This procedure may also be applicable to other dynamic penetrometer tests. Engineering properties can be estimated on the basis of empirical correlations between N-values and soil density, strength or stiffness. General terms and conditions Cookies och Javascript Disclaimer Contact. The quality of the result produced by this standard is dependent on the competence of the personnel performing it, and the suitability of ashm equipment and facilities used. Read more about SIS Subscriptions.

The Standard Penetration Test is astn most common type. Referenced Documents purchase separately The documents listed below are referenced within f4633 subject standard but are not provided as part of the standard.

The procedures used do not consider material variation, purpose for obtaining the data, special purpose studies, or any considerations for the user’s objectives; and it is common practice to increase or reduce significant digits of reported data to be commensurate with these considerations.

  COPPELIA KAHN THE ABSENT MOTHER IN KING LEAR PDF

ASTM D4633 – 16

This energy measurement procedure can evaluate variations of N-value resulting from differences in the hammer system. See also Refs 1- 6. Link to Active This link will always route to the current Active version of the standard. Subscribe on standards with our subscription service. Your shopping cart is empty. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. The N-value depends on the soil properties but also on the mass, geometry, stroke, anvil, and operating efficiency of the hammer.

Subscribe on standards – Read more. The inch-pound units given in parentheses are mathematical conversions which are provided for information purposes only and are not considered standard. Report error on page.

Sustainable Development Goals and standardisation, how do they connect? It is not intended for use with down-hole hammers. Users of this standard are cautioned that compliance with Practice D does not in itself assure reliable results.

Please note that the selected standard is invalid. Since the measured energy includes the extra potential energy effect due to the set per blow, tests for energy evaluation of the hammer systems should be limited to moderate N-value ranges between 10 and 50 Ref 7.

ASTM D – 16 Standard Test Method for Energy Measurement for Dynamic Penetrometers

Contact us svenska Login. It is not intended for use with down-hole hammers.

  EL VELLOCINO DE ORO ROBERT GRAVES PDF

In this system, the pound lbf represents a unit of force weightwhile the unit for mass is slugs. Valid Buy this standard.

This procedure may also be applicable to other asstm penetrometer tests. These notes and footnotes excluding those in tables and figures shall not be considered as requirements of the standard.

In this system, the pound lbf represents a unit of force weightwhile the unit for mass is slugs. When you use our service you can be assured the latest editions and easy access.

ASTM D – 05 Standard Test Method for Energy Measurement for Dynamic Penetrometers

The standard is now in your shopping cart. Message to your colleague.

Reporting of test results in units other than SI shall not be regarded as nonconformance with this test method. Soil and Rock I: Shopping cart Close cart 0, foreach: Historical Version s – view previous versions of standard.

Reliable results depend on many factors: Alternatively, the N-value can be used directly in foundation design using correlations to design parameters such as allowable bearing pressure or pile capacity. In addition, they are representative of the significant digits that d463 should be retained. It is beyond the scope of this standard to d463 significant digits used in analytical methods for engineering design. Practice D provides a means of evaluating some of those factors.

Author: admin